BLACK FRIDAY50% off your first 3 months of CalcWood PROEnds in $29$14.50Get 50% off →
✕
My Account
Logged in with license:
-
Assigned email:
-
Valid until:
-
Loading history...
Loading history...
Enter the world of CalcWood and get unlimited access to ALL calculators.Unlock expert features PRO, detailed PDF plans, a personal account with a project archive, and much more. See everything you get
I already have a License Key+
Key not at hand? I'll email it to you
Enter the email address your key was sent to and I'll send it again.
Enter the parts you need. The calculator lays them out on store boards with as little waste as possible and tells you how many boards to buy and how to cut them.
More than volume: a cut list with saw kerf, cost, waste and weight, so you know if you can haul it home.
Projects calculated:0
Need help with the terms?
Practical tips and quick search in the knowledge cards are waiting below.
Not sure where to start? Try an example:
1. What do you need to cut??
Each row is one size in millimetres. The name is optional, it shows up in the shopping list and PDF.
Example – replace it with your parts.
NameQtyThickness [mm]Width [mm]Length [mm]
2. Lumber you'll buy
Lumber to buy?
With ripping the calculator suggests one board per thickness, as wide as the widest part; without it a board for every part section. Fill in the length and width your store sells. An edited row stays as it is. More lengths or widths = more rows.
Thickness [mm]Width [mm]Length [mm]
Just fill in the length your store sells.
Offcuts you already have?
Enter the lumber pieces you already have at home or in the shop. The calculator cuts what it can from them and only then plans what to buy for the rest. Offcuts are not end trimmed, their ends count as square.
Got offcuts at home? Add them and the calculator uses them before it tells you what to buy.
QtyThickness [mm]Width [mm]Length [mm]
+
-
+
-
In inches the calculator uses rough thicknesses per NHLA rules: 9/16″ finished comes from 3/4, 13/16″ from 4/4, 1 1/16″ from 5/4, 1 5/16″ from 6/4, 1 1/2″ from 7/4 and 1 3/4″ from 8/4. A thickness written as x/4 means rough thickness. Softwood dimensional lumber (2×4 etc.) is counted by nominal size.
3. Optional
+
Price and wood
+
-
remembered from last time ·
+
-
Cutting
PRO· changed
You can change the cutting settings. Once you do, PRO unlocks the shopping list and cutting plan. Board count, volume, cost and weight stay free.
You rip parts of different widths from one wider board, then cut them to length – table saw, panel saw or track saw. Off = every part from a board of its own width.
+
-
+
-
+
-
What PRO unlocks for your lumber
Ripping on the table saw with the cheapest way picked for you – you see right away how much you save
Projects over 10 different parts, My lumber and the store PDF with cutting plans
Buying and At the saw: check off purchases and cuts on your phone – plus every CalcWood calculator
Saved projects, calculation history and higher limits for faster work
Enter the email address your key was sent to and I'll send it again.
Not buying right now? Tell me why in one click:
✕
Payment successful!
Thank you for your purchase.
Your license key has been sent to your email inbox. Check your spam folder too.
Redirecting to key entry in 15 s
PRO
Enter your license key
Paste the key from your email below and unlock all PRO features.
Black Friday
First 3 months
Offer ends in:
0days00hrs00min00sec
Technical drawings and PDFs with dimensions
Cutting plans and higher calculation limits
All calculators in one subscription
Saved projects, calculation history and much more
After the offer period the subscription renews automatically at the regular price. You can cancel it anytime in the customer portal, and PRO stays active until the end of the paid period.
Privacy and cookies
I use essential cookies and local storage to keep CalcWood working properly, including language settings, security and Stripe payments. I may also use optional analytics to understand how the calculators are used and improve them. Learn more.
Shortcuts work while the cursor is in the parts list.
Add parts
Say or type for example: “4 shelves 3/4 by 11 1/4 by 32 inches, 2 sides 3/4 by 11 1/4 by 6 feet”. Quantity, name and three sizes; separate parts with a comma or “and”. Each number can have its own unit. Dictation is handled by your browser (in Chrome by a Google service).
From Excel or Google Sheets: copy the rows with your parts and paste them with the button above, or on a computer click into the parts list and press Ctrl+V.
+
-
+
-
+
-
+
-
Where should I send the plan? 📩
I need your email to deliver the generated plan. I’ll occasionally send you news and offers about CalcWood calculators and plans too. Unsubscribe any time with one click in any email. Privacy
Data is used for optimization (the calculation is the same for both).
⚠️ Please select if you are a DIYer or a Professional.
Please enter a valid email.
Working on it...
Sent!
Go to your email inbox and you will find your calculation there 💪 (printable PDF format).
Window will close in 5 s
What the lumber calculator helps you with
Offcuts from your shop: Save the offcuts you have at home. The calculator spots which ones fit your parts, cuts what it can from them, and you only buy what is missing. After cutting, save the new offcuts for your next project.
Buying for a build: Deck, fence or framing. Get the board feet and know right away how many boards to grab and what it costs.
Furniture from finished parts: Enter shelves, sides and rails, the calculator lays them out on the boards your store sells.
Hardwood by volume: From finished thickness I work out the rough stock (4/4, 5/4, 8/4) and how many board feet to order.
Checking the price: The store sells per board foot, per linear foot or per piece? Enter the price exactly as listed.
Hauling: By wood species I estimate the weight, so you know if your car or trailer can take it.
A list for the store: Share the calculation by link, with PRO download a PDF with the cut plan.
Lumber is expensive and most of it gets wasted by a badly planned purchase. This is what works for me:
The calculator offers your offcut PROSave your offcuts in My wood. On every calculation the calculator checks them, and when one fits the parts you are cutting, it offers it with one click. You only buy what is missing.
Log offcuts right after cuttingSave what is left with one button or by hand. Add a note, like “painted end, in the garage”, so you know where to find it.
Not every scrap is an offcutSet the smallest useful offcut. Shorter pieces count as waste, so your shop does not fill up with scraps you will never use.
Parts first, boards secondDo not buy by eye. List the finished parts, lay them out on boards and only then drive to the store. You save money and a second trip.
Do not trust board endsEnds are often checked and out of square. I trim at least 3/8″ off each end, more with kiln-dried hardwood.
Kerf adds upAn 1/8″ kerf looks like nothing. With ten parts from one board it is over an inch and suddenly a part does not fit.
Waste depends on the woodSurfaced softwood is fine with 10–15 % waste. Rough hardwood with knots and checks can easily need 25–30 %.
4/4 is not 1 inch finishedRough 4/4 hardwood planes down to about 13/16″. Need a full 1″? Buy 5/4. The calculator picks the rough thickness for you.
A 2×4 is not 2 by 4Dimensional lumber is sold by nominal size. A 2×4 measures 1 1/2″ × 3 1/2″, but you pay board feet for 2″ × 4″.
Use your own pricesLumber prices change every month and every store counts differently. That is why I never make up prices, you enter yours.
Weight is an estimateI calculate weight at 12 % moisture content. Green lumber from a sawmill is much heavier, plan your hauling with that in mind.
Longer boards often winA longer board often fits the parts better and leaves one usable offcut instead of two short scraps. Enter several lengths and compare.
Shop tip: Before you head to the store, enter your finished parts and what the store sells. You get the exact board count and the offcuts.
Can the calculator use the offcuts I already have?
Yes. In step 2, enter the offcuts you have (count, thickness, width, length). The calculator cuts what it can from them and only then plans what to buy for the other parts. The shopping list, cut list and PDF all show what comes from offcuts and what you buy.
How does the calculator know which offcut fits?
With PRO, save your offcuts in My wood in My workshop. On every calculation the calculator checks them, and when some fit your parts it offers them with one click. After cutting, one button removes the used pieces and adds the new offcuts. Pieces shorter than the smallest useful offcut count as waste.
Can I download the list to Excel and print part labels?
Yes. Below the result there is Download Excel (parts, shopping list and cut list on separate sheets). With PRO you also get part labels for an A4 sheet of 24 labels 70 × 37 mm: each piece gets its number, name, size and the board it comes from.
How many boards should I buy?
List your finished parts. Add the saw kerf and end trim to each one. Then lay the parts out on the lengths your store sells, so every part sits whole on one board. The number of boards you end up with is what you buy. The calculator does this for you: enter the parts and the store lengths and you see the board count and the offcuts.
Most board foot calculators only give you volume, and cut list optimizers want you to enter the boards yourself. This one starts from your finished parts and suggests how many boards to buy in store lengths and how to cut them, plus volume, cost and weight. The calculation is free, the shopping list and cut list are free for up to 10 different parts.
What is a cut list?
A list of which parts you cut from which board, and in what order. The calculator builds the cut list for you: for every board it shows the parts, the kerfs and the offcut, so in the shop you just measure and cut.
How do I calculate board feet?
Multiply thickness in inches × width in inches × length in feet and divide by 12. A 1″ × 6″ board 8 feet long is 1 × 6 × 8 / 12 = 4 board feet. The calculator above does it for your whole list and adds waste.
How many board feet is a 2×4×8?
5.33 board feet. Softwood stores count from the nominal size 2″ × 4″, even though the stud really measures 1 1/2″ × 3 1/2″.
Why did the store charge more board feet than my parts?
Hardwood is tallied before planing, thicknesses under 1″ count as 1″ and the area is rounded to whole square feet (NHLA rules). Open “Why did they charge you more?” under the results.
How do I convert board feet to cubic meters?
1 board foot = 0.002359737 m³ (144 cubic inches). Multiply board feet by 0.00236 to get cubic meters. The other way: 1 m³ ≈ 423.8 board feet.
Board feet
Cubic meters
10 BF
0.024 m³
50 BF
0.118 m³
100 BF
0.236 m³
How do I convert price per board foot to price per linear foot?
Price per linear foot = price per board foot × thickness″ × width″ / 12. A 1×6 has 0.5 board feet per linear foot, so at $8 per board foot a linear foot costs $4. The other way, divide the linear foot price by that number. The calculator takes the price per board foot, per linear foot or per piece, enter it exactly as listed.
How much does lumber weigh?
It depends on the species. I use specific gravity at 12 % moisture content from the USDA Wood Handbook (FPL-GTR-282). Green lumber is much heavier.
Species
lb per board foot
kg per m³
White oak
≈ 4.0 lb
≈ 762 kg
Red oak
≈ 3.7 lb
≈ 706 kg
Hard maple
≈ 3.7 lb
≈ 706 kg
White ash
≈ 3.5 lb
≈ 672 kg
Black walnut
≈ 3.2 lb
≈ 616 kg
Black cherry
≈ 2.9 lb
≈ 560 kg
Yellow-poplar
≈ 2.4 lb
≈ 470 kg
Southern yellow pine (loblolly)
≈ 3.0 lb
≈ 571 kg
Douglas-fir (Coast)
≈ 2.8 lb
≈ 538 kg
Western redcedar
≈ 1.9 lb
≈ 358 kg
Does it make a sheet cut list?
No, here I handle boards and beams lengthwise (one dimension). Cutting sheet goods is a separate topic.
Does it calculate firewood or logs?
No, this calculator is for sawn lumber: boards, beams and battens. Firewood is sold by the cord, which includes the air between the pieces, and log volume uses a different formula based on the log diameter.
Ratings & Reviews
Checking calculator ratings...
Loading reviews...
✕
Did the calculator help you?
Rating:
Your feedback helps improve CalcWood for all woodworkers and DIYers around the world.
✓
Thanks a lot for your review!
Your review has been submitted and is waiting for my approval. If you provided an email, I'll let you know as soon as I reply!
!
Already rated
A review has already been submitted from your IP address. Thanks!
UPDATES & CHANGELOG
+
v1.10 (November 2026)
Offcuts from your shop: enter the offcuts you have at home, the calculator cuts what it can from them and you only buy what is missing. It offers your saved offcuts when they fit your parts.
My wood: your store lumber and offcuts at hand in My workshop, with a short note. After cutting, save the new offcuts with one click.
Smallest useful offcut: a shorter piece is waste, a longer one can be saved for the next project.
Whole board, no end trim: a part as long as the board gets the whole board, so the list is complete.
Excel and labels: download to Excel and print part labels on an A4 sheet.
v1.00 (November 2026)
Volume right away: board feet and cubic meters, linear length, area, weight by species and cost by your yard's price list.
Shopping list: from finished parts I work out how many boards to buy and lay the parts out on them with kerf and end trim.
Lumber by volume: rough thickness per NHLA rules (13/16″ from 4/4) or with your own planing allowance.
Have a suggestion or found a bug? +
Your opinion matters. If you discover a bug or have an idea for a new feature, be sure to write to me. (Please write your message in English) 💡 Your current calculator configuration will be automatically attached to help me debug the issue.
One rolling bench for your table saw, router and assembly work. The saw sits flush with the top, so you get a big flat surface around the blade, and the whole bench rolls wherever you need it.
Ratings & Reviews