Designing and assembling drawers has clear rules. Here are 21 practical points, ordered from the most important setup decisions to workshop details that save time, nerves, and material:
Drawer box width for side-mount slidesStandard ball-bearing side-mount slides need 1/2″ (12.7 mm) of clearance on each side. Drawer box width = clear opening width minus 1″. A 21″ opening takes a 20″ wide box (outside width). The calculator uses 1/2″ per side by default. If your slides need a different clearance, change Slide Thickness / Gap.
Drawer box size for undermount slides (Blum)For Blum TANDEM and MOVENTO the calculator deducts 21 mm (about 13/16″) per side minus the drawer side thickness. The inside width between the box sides is always the opening width minus 42 mm (about 1 5/8″). With 5/8″ sides, the outside box width is the opening minus 10.25 mm (about 3/8″). Box length = slide length.
Splitting cabinet height into drawersFront height = (cabinet height − 2 × perimeter gap − gaps between fronts) ÷ number of drawers. The calculator starts with a 2 mm (about 1/16″) perimeter gap and 3 mm (about 1/8″) between fronts. Example: a 30″ tall cabinet with overlay fronts and 3 drawers gives three 9 7/8″ fronts. Box height = front height minus the top and bottom overlay.
Start with the correct cabinet dimensionsFirst decide whether you are entering the outside cabinet size or the clear inside opening. The calculator can handle both. If you already know the inner opening, set cabinet material thickness to 0 so the side panels are not deducted twice.
Drawings: put the tape on and markBelow the results you get up to 6 technical drawings (fronts, cabinet with drawer boxes, side with drilling axes, top view, box section and, for undermount slides, drawer machining), also in the PDF for the workshop. Every height is measured from the outer bottom edge of the cabinet, exactly like the drilling table. You see where the fronts go, where to drill and how much space is left behind the drawer.
Exact internal width (LW)With undermount slides, every millimeter counts. Always measure the internal width (LW) after assembling the cabinet. If you are off by more than 1 mm, the slides will rub or won't click in at all.
Installing Blum for the first time?If you are working with undermount slides for the first time, download the original PDF manual for or . You will find all the mounting dimensions there.
TANDEM vs. MOVENTOTANDEM is a solid base for standard drawers and mainly gives height adjustment. MOVENTO is a more precise and more comfortable solution with higher load options and 4D adjustment. For wide, heavy, or highly visible drawers, MOVENTO usually makes more sense.
Thicker drawer material than the manufacturer recommendsUndermount slides are made for drawer sides up to 16 mm. Your boards are 18 mm (up to 19 mm works)? The calculator keeps the box the same width, narrows the front and back panels and the bottom, and the Box section and Drawer assembly drawings show the rebate to mill from below on the inside of the side down to 16 mm. The manufacturer does not recommend this.
Overlay vs. Inset frontAn overlay front covers the cabinet edges and hides small inaccuracies more easily. An inset front sits flush with the cabinet edge. It looks cleaner, but needs a precise square cabinet and well-controlled gaps.
Gaps between frontsA common front gap is 2 to 3 mm. Too small a gap shows every inaccuracy and fronts may rub. Too large a gap looks cheap. The calculator already includes these gaps when it divides the front heights.
Card trick for mounting frontsA workshop trick: take an ordinary deck of playing cards, place it in the gap, split it exactly in half, and use it on the left and right, or top and bottom. It helps center the front nicely without complicated measuring.
Slide length and typeSlides come in 50 mm steps. For an atypical depth, choose the nearest shorter slide – the drawer with the slide must stay shorter than the clear internal cabinet depth. Classic ball-bearing slides mount on the drawer side and need an exact side clearance, typically 12.7 mm on each side: a wider drawer rubs, a narrower one has play.
Individual front and box heightsIf one drawer needs to be taller, enter its front or box height manually. The calculator redistributes the remaining space automatically. This is useful for a deep bottom drawer with smaller drawers above it.
How to maximize capacityWith overlay fronts, there is dead space under the drawers. Normally, inner boxes are made the same height to stay interchangeable. If you extend them downward, you gain maximum storage. This calculator can calculate it in the Expert settings.
Cut list and cabinet quantityIf you are building several identical cabinets, use the cabinet multiplier. The cut list will then calculate all parts for all sets at once. This is more accurate for ordering boards, edge banding, and slides.
Edge banding and wood grainFor fronts, count with edge banding all around. For drawer boxes and cabinets, usually only visible edges matter. The calculator can use smart edge deduction and keep grain direction on fronts so the decor does not look like random offcuts.
Large and heavy drawers?For large drawers used for pots, tools, or supplies, choose higher load slides such as 40 kg or 70 kg. But the drawer construction must also carry the load, especially the bottom. You can check deflection in my .
3D preview: check itBefore you cut, rotate the model in 3D, hide the fronts or cabinet and play the opening. You will see at once whether drawers, slides and bottoms fit as expected.
Groove for the bottomRout the groove through both sides, the front and the back panel. Width = bottom thickness + 0.5 mm, depth 1/3 to 1/2 of the side (max 8 mm). Make the bottom 1 mm shorter per side and leave at least 10 mm of side above the groove.
Blum: back panel and bottomWith Blum the bottom sits 13 mm above the lower edge of the sides and the runner travels below it. Either groove the back panel and notch it at the bottom next to the sides for the runner end, or make it lower so it sits on the bottom – then no groove or notch is needed. Check the exact size in the instructions for your type (TANDEM / MOVENTO).
Ratings & Reviews